ecolina

ico_badges01

The ideal solution for small roof areas

The Ecolina sheet in ecotres® material is the ideal solution for covering small roofs such as those of verandas and gazebos, for agricultural buildings and livestock shelters, but also for erecting fences or cladding walls.

 The Ecolina range and its related accessories are made of ecotres® (a high-performance layered thermoplastic material patented by Tecno Imac), in part derived from recycled materials and itself 100% recyclable at the end of its life

 

Durable:

ico-v

  • Laboratory tests have confirmed the extreme longevity of Ecolina sheeting which comes with a 20-year Tecno Imac warranty (*)

Thermal and acoustic insulation features:

ico-v

  • The intrinsic insulation properties of the thermoplastics employed in the production of this product assure excellent thermal and acoustic characteristics

Flexible:

ico-v

  • The geometry and the elasticity of the material assure high degrees of curvature when laying the sheets on convex surfaces

Low-cost:

ico-v

  • Ecolina offers an exceptional value for money solution without compromising quality

Technical specifications

Standard length m 2/3/4/5/6
width mm 1.104
useful width mm 1.050
average thickness* mm 1,80
weight* kg/m2 3,60
thermal expansion coefficient °C-1 3,99×10-5
unitary thermal transmittance W/m2k 4,68
breakage load kg/m2 473
grigio-verde

green-grey

rosso-siena

siena

grigio

grey

terracotta-80x80

terracotta

The material

Ecotres is obtained by the convergence of three different individually extruded thermoplastic layers at a terminal extrusion head. The result is a single sheet that is stratified in three different layers, each of which has specific features designed to perform certain functions: (read here to learn more).

1-top layer: solid-coloured in PMMA (Methacrylate) for colours and finishes that are perfect and highly resistant to UV, weather and environmental exposure to chemicals of any kind.

 

2-middle layer: a mixture of different polymers loaded with micronized inert material, for a low thermal expansion, good acoustic behaviour and resistance to bending.

 

3-bottom layer: thermoplastic compounds for maximum resistance to impact and chemical aggression from underneath.The result of this particular combination of thermoplastic materials is a stable and resistant synthetic product, applicable to any environmental situation, without fear of attacks of acid vapours of any kind, whether industrial or agricultural, or the most aggressive saline environments.

Assembly tips

Roof sheeting must be laid on a framework of purlins whose span interval is proportional to the prevailing loads and the inclination.
Position the first sheet with the stamped-marking side facing towards the outside of the roof. After it has been aligned, secure it with its first crest aligned to the roof superstructure.

Warning: allow for normal thermal expansion by drilling the sheet fixing holes a bit wider than the fastening screw shank diameter, typically a 10 mm hole diameter for 6.5 mm screws.

Then the second line of fastenings should be fixed to the next higher purlin.
Establish an overlap between the second and first rows and fix the line of screws through the overlap. To maintain alignment, we recommend using a reference lanyard anchored to the ends of the purlin.

Proceed in a similar manner with the subsequent sheets, up to the last. If necessary, the width of the last sheet can be adjusted by trimming it with an angle grinder. When this has been done, proceed to secure all the sheets following the indications illustrated in the figure (at least four screw-down fastenings on each sheet per purlin, on all crests on the lowermost eaves gutter purlin).


part-ecolina1

Lateral overlap

The overlap must be made by positioning the crest of the next Ecolina sheet to be laid over the last previously laid one. Make sure to secure the next row of fastenings along the line of the overlap.

part-ecolina2

Horizontal overlap

The overlap must always be implemented along the line of the supporting purlin, to an extent of 15 to 30 cm, depending on the slope.

part-ecolina3

Sheet overhang

At the eaves gutter, the sheet overhang must not exceed 10 cm from the lowermost purlin.

Documentation

ico_download_pdfManuale di montaggio*
lastre leggere Italiano

ico_download_pdfvoce di capitolato*
lastre leggere Italiano